Back

Inconsistent spheronization results with difficult active ingredient?

The following case study demonstrates how the Caleva Mixer Torque Rheometer.  The MTR-3 was an invaluable aid in a specific case. A manufacturer of generic Venlafaxine pellets was experiencing inconsistent results from their manufacturing line. The resultant product was variable in both usable yield (weight of acceptable pellets as a % of weight of granulation made), and dissolution profile. The product was a registered pharmaceutical product with a 15% water content. It was not known why, or how, this liquid binder content was determined to be the optimum.

Since the formulation was already registered, neither the formulation ingredients nor the amount of liquid binder could be easily modified. The texture of the extrudate was visually inconsistent but no quantitative assessment of this casual observation had been undertaken. To assess this issue, the rheological properties of the customer’s granulation were examined in a quantitative way. From a practical standpoint this was only possible using the Caleva Mixer Torque Rheometer (MTR-3).

TRIALS
Two key parameters were examined with the MTR-3.

OPTIMUM BINDER CONTENT
An initial trial was performed to look at the effect of binder content on the consistency of the granulation. This was clearly recognised as important but in reality, could not be easily changed. In the original development the optimum binder concentration was determined by the “hand squeeze test” (a subjective assessment and not really appropriate for the 21st century pharmaceutical industry!). The effect of different amounts of binder content on the consistency of a granulation was assessed using a 20g (dry powder weight) sample. The results are shown in figure 1.

 

 Effect of different amounts of binder content on the consistency of a granulation was assessed

 

GRANULATION TIME
In the original development, no quantitative assessment had been undertaken of the influence of mixing upon the formulation properties, possibly because it was assumed that no appropriate tool was available to provide a quantitative measurement or that this factor was considered to be of little significance to the final formulation providing it was granulated “enough”. Within the registration, some flexibility was permitted in the amount and intensity of mixing. There was scope for changes to be made in this area. An assessment was made using an MTR-3 of the effect of mixing on the consistency of the formulation. This assessment was again made utilizing a 20g (powder dry weight) sample. The instrument was used to measure the consistency of the material in the bowl as the granulation progressed. The results are shown in Figure 2.

 

Measure the consistency of the material in the bowl as the granulation progresses

 

RESULTS

Binder Content
For pellet formulations, an ideal % binder content is generally somewhere just before the maximum consistency reading is reached. These results show that the 15% binder content that is used in this formulation is unlikely to be optimum for this product. In this case the results suggest that a water content of about 35% is optimum in this formulation. However, as the formulation was already registered with the authorities with a water content of 15% the manufacturer, understandably did not want to change this value. The early assessment made using the “hand squeeze test” and without any quantitative data is inadequate and is likely to be a contributing factor to the quality problems encountered in production. The formulation will never be “optimum” as the binder ratio cannot practically be changed due to product registration.

Granulation Time
A similar problem was apparent with the granulation time given to the formulation. The results (Figure 2 above) show that the granulation regime was of paramount importance if consistent production quality was to be realized in practise.

DISCUSSION
Quantifiable measurements of formulation consistency are a necessary (or at the very least desirable) part of formulation development if issues with formulations are to be minimized and optimum yields achieved once they get into production. Whilst the importance of the percentage of binder liquid added to a formulation is recognised as important to achieve optimum production quality, many formulators who work in formulation development still rely on subjective and non-quantifiable assessments. The importance of the granulation program is sometimes not recognised as a significant factor in formulation development. Contrary to this general perception the granulation process should be consistent in its operation and assessed in a quantitative way as a standard part of product development. When used as a fundamental part of formulation development processes the Caleva Mixer Torque Rheometer can be instrumental in avoiding later problems in production and is the collection of quantitative data recommended as a standard part of the development process.

CONCLUSIONS
There are three main ways available to determine the optimum ratio and mix time:-

  1. Adding binder and testing by ‘eye and hand’ to reach an estimated optimum ratio. Obvious limitations and no reproducibility!
  2. The systematic investigation of a range of possible options with subsequent testing of the final characteristics of tablets and spheroids (pellets) produced. A time-consuming and laborious undertaking!
  3. Using the Caleva Mixer Torque Rheometer (MTR-3) the only method that is objective, repeatable, quantifiable and rapid.

 

Dr Steve Robinson
By Dr Steve Robinson
1 May 2020 in Mixer Torque Rheometer

Leave A Comment

 

 

 

Talk To Caleva

Overcoming Consistency Challenges in the Iron Making Sector

Caleva's International Sales Manager Steve Mate visited the Department of Chemical Engineering at Osaka Metropolitan University to find out how the Mixer Torque Rheometer (MTR) is being used. Read More

Measuring and monitoring your formulation

Did you know that the Mixer Torque Rheometer (MTR) is designed to carry out 3 separate experiments essential to your formulation development and production? Read More

Book a live online demonstration with Caleva

Are you interested in one of our products and would you like to see it in action? We provide free R&D system demonstrations live online via video conference wherever you are in the world. Scott Humphries or Steve Mate will demonstrate and explain advanced equipment features and allow you to see ... Read More

Shaped Catalyst Body Preparation with MTR and Caleva Screw Extruder

Shaped Catalyst Body Preparation. Zeolite HZSM-5 (ACS Materials, M38) was mixed as a dry powder with alumina (Sasol, Catapal D (Boehmite)) and the required amount of Milli-Q water to ensure an optimum solid-to-liquid ratio for extrusion (measured using a Mixer Torque Rheometer, Caleva). The paste, c... Read More

Caleva explain the basic Mixer Torque Rheometer concepts - Video

The MTR can process from 10g to 25 g of your material, depending on the formulation, meaning barely any material is wasted in experiments. The machine will very quickly tell you the ideal amount of liquid to add. The user may have a start point in mind but this may result in a formulation that is to... Read More

Opportunities for Mixer Torque Rheometry

Wet granulations are a useful precursor to many solid dosage formulations and as such are widely used in the pharmaceutical industry. Because of the diverse nature of pharmaceutical materials, granulation is often employed as an intermediate process to enhance flow and compaction properties and impr... Read More

How much product should be used in the MTR and how accurate is it?

How much product do you use? The answer is that this is always product specific. This is demonstrated in this article. In these experiments the MTR is used in the multiple addition mode whereby increasing binder content is automatically added to different masses of product. The Caleva Mixer Torque R... Read More

Can temperature during granulation influence formulation consistency?

The temperature of the mix during granulation processes is generally considered to be of minor significance in both formulation development and in large batch granulation despite the fact that in some locations ambient temperature can change significantly during the course of a working day. The MTR ... Read More

A Tool for Pre-Formulation Assessment of Excipients

Excipients from different batches or vendors may vary in quality and it is often necessary to perform pre-formulation assessment for each new batch of excipient received. Read More

How long should I granulate my materials?

Variable Mix Time Test It is well-known that a minimum amount of mixing is required to ensure consistent and repeatable product characteristics. What is often less considered is the possibility of over-mixing the product so that the characteristics of the resulting formulation undergo a change. Read More

How Do You Ensure Consistency During Scale Up?

The Mixer Torque Rheometer's Consistency Test To ensure consistency is maintained during scale up and production, the Mixer Torque Rheometer can be used to perform a quick and simple test which monitors the consistency of the wet granulation during the mixing phase. This test can be used whether you... Read More

Formulation development - determine optimum powder to binder ratio

Multiple Addition Test Binder liquid is added to a dry powder mix and the consistency is measured as the mixing and addition of binder progresses. The consistency of the mix is measured at regular periods so that the relationship between the amount of liquid binder added to the mix and the consisten... Read More

What characteristics should my extrudate have?

Extrusion and spheronization is not always completely straightforward. A formulation required for spheronization needs to go through the following processes and achieve the following properties. Read More

How to produce consistent formulations from different mixers

Customer Quote: Mr. K.S (Aurobindo) "It is exciting to see the correlation between the two graphs and granulation end point". With a major pharmaceutical manufacturer, together we characterised all their various mixers to produce a consistent formulation. To identify three important characteristics ... Read More

Do excipients purchased from different vendors behave in the same way?

The Mixer Torque Rheometer can be used to assess the behaviour of excipients purchased from different suppliers. Background Excipients from different batches or vendors may be variable in quality and it is often necessary to perform pre-formulation assessment for each batch of excipient received. In... Read More

The Caleva Family of Laboratory Equipment

Whilst you may have heard of Caleva and any one of its flagship pieces of equipment, we'd like to introduce you to the family of Caleva laboratory equipment that you may find helpful for your application in your industry sector. Choose one process or choose all of them. Select further functions as y... Read More

Inconsistent spheronization results with difficult active ingredient?

The following case study demonstrates how the Caleva Mixer Torque Rheometer. The MTR-3 was an invaluable aid in a specific case. A manufacturer of generic Venlafaxine pellets was experiencing inconsistent results from their manufacturing line. The resultant product was variable in both usable yield ... Read More

Mixer Torque Rheometer used with Food Powders

Research Article University of Padova where their Caleva Rheometer was used Abstract Vegetable soups are complex mixtures containing vegetables in different percentages, thickeners, salt, fat, and emulsifying/wetting agents. When prepared as dehydrated powders in convenience foods, they need to be r... Read More

The Importance of End Point Detection Consistency

This world is not only for us. Can you imagine world had no animals, what would it be like? Would the trees be green? Without birds or squirrels, less trees would grow. There would be no pets, no flowers and no bees. If even one part of our ecosystem is removed, we will all die. Without animals, we ... Read More

Caleva Multi Lab & Bone Regeneration study Medical University Gdańsk

Drug-loaded mesoporous silica/calcium phosphate composites for bone regeneration Adrian Szewczyk at Department of Physical Chemistry, Faculty of Pharmacy, Medical University of Gdańsk has kindly allowed us to introduce this paper that introduces a study of Drug-loaded mesoporous silica/calcium phosp... Read More

Agglomeration properties of gluten-free flours under water addition and shearing conditions

The different states of agglomeration were identified by the evolution of rheological properties under water addition and shearing conditions using a Caleva® mixer torque rheometer. Read More

How reproducible can measurements be of something that is not homogeneous?

The MTR-3 uniquely offers a means of characterising the rheological properties of a wet granulation by providing a quantitative value of the consistency of the material tested. The more traditional hand squeeze test, previously widely used, to measure or compare granulations, is falling into disrepu... Read More

Yield Problems in Production and Quality Control

One of the strengths of the Caleva Mixer Torque Rheometer (MTR-3) is that it can be used to verify the properties of wet powder mass samples taken during production in large scale mixer/granulator systems. Read More

How the Mixer Torque Rheometer resolved a tablet friability issue

Caleva worked closely with a well known producer of food supplements made from natural materials, plant extracts and other natural food sources. Their tablet formulations work well and this nutraceutical company has a good reputation for their products. Generally they do not encounter problems with ... Read More

Determination of moisture requirement to prepare spheroids by extrusion-spheronization

Spheroids are popularly used in the design of multi-particulate drug delivery systems. Extrusion and spheronization is commonly employed to manufacture spheroids in the pharmaceutical industry. It is a multiple-step manufacturing process which could be summarized into the flow chart as shown in Figu... Read More

Save Time and Cost in Formulation Development

In the mid 1990’s, the field of pyrotechnics was limited mainly to applications in aircraft ordnance, fireworks and rock blasting. This has been developed to a highly advanced science and is an extensively used technology which finds application in spacecraft, aircraft and underwater vehicle systems... Read More

End Point Determination Using the Caleva Mixer Torque Rheometer

A company wished to move a formulation currently undergoing product development from small scale laboratory (with batches of 50 grams) to the next stage for a larger scale batch trial of 100 kg (scale–up). The development had been started using a small Caleva Multi Lab bench top mixer (maximum batch... Read More

The importance of mixing time for formulation development

It is well established and understood that one of the most important factors in the development of a formulation for both tableting and making pellets by extrusion and spheronization is the amount of liquid binder added to the formulation. What is less widely acknowledged is the importance of mixing... Read More